ads' corner

HP Color LaserJet: Unable to connect to the network

We have a HP Color LaserJet in the office, one of these devices which can do both printing and scanning. The newer versions include a very nice feature “Scan to network folder” - so I did setup options to scan different PDF sizes to all of our laptops. Very convenient!

Until it stopped working a while ago.


SMART error (ErrorCount) detected on host - but the NVRAM disk is perfectly fine

Recently I got a new system with a NVRAM disk (nice and fast). Upon installing smartmontools, it started reporting that the error counter for the disk is increasing. For a brand new disk?


Raspberry - Raspbian - First steps

Installing a new Raspberry Pi is always the same few steps, and still I have to look them up almost every time. Here is the summary.


Reading data from my Scuba Diving computer after Linux removed IrDA support

When I go Scuba Diving, I use two diving computers. It’s always good to have a fallback, right? My main computer is a ScubaPro Uwatec Galileo Luna. That’s a wrist mounted computer with hoseless air-integration. That means that a sender is connected to the first stage of the regulator, and it transmits data to the wrist computer. In addition the computer records data like depths, consumption, temperature, alarms ect. My fallback is an air-integrated console mounted Suuntu Cobra. I check this computer too when I’m under water, but mostly for the most conservative reading for the safety stop.


Replace and re-add a failed drive to a Linux software RAID

Most of my systems run on a software RAID 1 configuration (that is, two disks, where each disk is mirrored to the other). This way, one of the disks can fail and still all the data is available.

If a disk failure happens, the disk is replaced with a similar disk, and then needs to be configured and re-added to the RAID.


Avoid "wear out" of SSD-cards in an openHAB system

You might know that problem: the brand new SSD in your system is super fast, but after a good time using it, the card is dead. Unlike spinning disks, which usually fail over time, and show I/O errors by blocks, SSD cards are prone to a problem called Wear leveling. Blocks which are written more often will “wear out”, and become unresponsible. More writes increase this risk. And a typical openHAB system does a number of writes all the time: every time an external status changes, it’s written to the event log. By default the syslog is written to disk as well, and then there is a myriad of systemd services, writing status information into files.


Huawei P10

It was time to pick a new mobile phone for myself. Not being very happy with the Samsung I have from my employer, I compiled a list of decent Android phones, and looked into each of them. In the end, I settled with the Huawei P10.


How to prioritize Wi-Fi connections on Android

At home I have two different Wi-Fi networks, both known to all my mobile devices. One is our internal network, password protected. The other one is an open Freifunk network. It’s nice to walk around in the village and automatically connect to other Freifunk Wi-Fi routers, instead of using expensive mobile data.

But when at home I really want my devices connected to our internal network. Makes it easy to copy files between devices, or access services only available in our internal network. Plus the native Wi-Fi connection is much faster than the Freifunk connection, which is limited by the speed of the VPN.


Most annoying Samsung mobile "features" - Part 2

About two years ago, I wrote about a long list of annoying features in my then Samsung S5 device (company issued). A while ago I got a Samsung S6 - so it’s time to see if Samsung came around and fixed items on the list.

The good news is that some of the really annoying “features” are gone. No more unnerving sounds when the device is fully charged, no more mandatory warning about sealing the USB port cover when unplugging from the charger (this might have to do with the fact that the S6 is no longer waterproof). Lock screen timeout slightly increased, but you also have to slide up to unlock the device - it no longer presents the keyboard by default. S Finder is gone - who did ever use this one anyway?


Most annoying Samsung mobile "features"

Android is a very nice operating system, people like it because it’s highly configurable. One of the major players in this game - Samsung Mobile - annoys it’s users with certain “features”, which you mostly can’t switch off or get rid off.

Even more annoying - for me - that’s the only Android option I get offered by my employer. The alternatives are iPhone, or Blackberry. So not really an option. Two years ago I switched to a Samsung S3, and a few weeks ago it was time to renew the contract, so shortly before Christmas there was a box with a shiny new S5 waiting for me in the office. Using the new mobile for two weeks now, I realized that Samsung remains true to themself and added more annoying functionality over the past two years.

Samsung is churning out dozens of different mobile devices every year. Maybe they should hire a few User Interface designers, or simply start using their own stuff, and see how annoying it is to use.