ads' corner

Replace and re-add a failed drive to a Linux software RAID

Most of my systems run on a software RAID 1 configuration (that is, two disks, where each disk is mirrored to the other). This way, one of the disks can fail and still all the data is available.

If a disk failure happens, the disk is replaced with a similar disk, and then needs to be configured and re-added to the RAID.


Weather Forecast in openHAB based on OpenWeatherMap, using Ansible

After setting up OpenWeatherMap in openHAB, I had another project on my list: send a forecast for the next day.

That is rather easy to do with a Cron rule.


Install OpenWeatherMap in openHAB, using Ansible

Next item on my home automation todo list: weather, and forecast. No good system without that data!

After exploring the options which openHAB supports, I settled for OpenWeatherMap. Note: you need an account with OWM, the basic functionality is free, the paid options give you more and better forecast.


Avoid "wear out" of SSD-cards in an openHAB system

You might know that problem: the brand new SSD in your system is super fast, but after a good time using it, the card is dead. Unlike spinning disks, which usually fail over time, and show I/O errors by blocks, SSD cards are prone to a problem called Wear leveling. Blocks which are written more often will “wear out”, and become unresponsible. More writes increase this risk. And a typical openHAB system does a number of writes all the time: every time an external status changes, it’s written to the event log. By default the syslog is written to disk as well, and then there is a myriad of systemd services, writing status information into files.


Configure a FRITZ!Box in openHAB, using Ansible

A while ago I posted about adding a Fritz!Box to openHAB, using Ansible. Now I had to use the Playbook to install another Raspberry, and found that some parts are missing in my posting. Mostly at the end, when it comes to configuring the Fritz!Box.

Therefore let’s run over all the steps again, and make sure that everything is covered.


if-up and if-down scripts with systemd

Everybody likes systemd, right? Well, not everybody. Who thought it might be a good idea to replace existing init systems with something which is big, monolithic, and not even feature complete?

A simple task: execute a script when an interface comes up, or goes down.

In the old days, on Debian or Ubuntu, one just added pre-up and post-down scripts in /etc/network/interfaces. But now, that file is gone, or empty. Ubuntu comes with netplan, which nobody else seems to use - luckily. NetworkManager is not used all the time, so one can’t depend on that either. And systemd does not have an option to do something simple like taking care of interfaces coming up and down. You can write yourself a target, but that only fires for the first time, not every time.


openHAB: redirect port 8080 to port 80

The openHAB Raspberry image, by default, listens on port 8080. After using the image for a while, it became quite boring to always add the port to the URL. Quickly I decided to redirect port 80 to port 8080, and make my life easier.

Not sure how much work that is in the openHAB settings, I settled with redirecting or forwarding the port 80 to port 8080.


Notification when washing machine or dryer are finished, with openHAB

As part of my home automation project, I wanted the washing machine and the dryer to send notifications when they are finished. Both machines are in a separate room, and their alarm beeps are hard to hear in the other parts of the flat. Also because of the noise both machines make during operation, the door is usually closed.

After checking several options how to interact with the washing machine and the dryer (from listening to the audio signals to having light sensors glued over the status led, open the frame and install something inside, and a small cam with picture recognition), I settled with measuring the power consumption. Next step: find the right kit.


Add a FRITZ!Box to openHAB, using Ansible

Next step on my way to add home automation: the FRITZ!Box. Mostly for the current IP-address, and call information.

After some research it became obvious that more manual work is required, hence again something which can be automated.


Update openHAB Things configuration using Ansible

In my earlier openHAB blog posts I automated the installation of extensions and linking of Channels to Items. Another problem I’m facing is the configuration of items. Again, that’s very easy in the UI - if you are willing to click through the list of Items, and manually do all the steps.

Among other things I’m using the binding-yahooweather and the binding-ipp bindings, and the first one needs configuration before it can work properly. For the second one, it righly discovered a laser printer in our network, but occasionally when openHAB requests the status information, this spins up an internal disk in the printer. Therefore it is feasible to increase the time between checks - it’s just the number of outstanding print jobs anyway. Doesn’t matter if someone reacts 5 or 15 minutes later, if the problem was not discovered instantly.